Rearuh

Dual-contour wing mirror. Large inboard convex surface is separated from small outboard aspheric surface.

Fender mirror on a Toyota Celsior

Wing mirror with integrated turn signal repeater

Side mirror with warning legend

A wing mirror, also known as the fender mirror, door mirror, outside rear-view mirror or side view mirror, is a mirror found on the exterior of motor vehicles for the purposes of helping the driver see areas behind and to the sides of the vehicle, outside the driver's peripheral vision (in the 'blind spot').

For mirrors on bicycles and motorcycles see "Rear-view mirror".

Although almost all modern cars mount their side mirrors on the doors—normally at the A-pillar—rather than the wings (the portion of the body above the wheel well), the term "wing mirror" is still frequently used.

The side mirror is equipped for manual or remote vertical and horizontal adjustment so as to provide adequate coverage to drivers of differing height and seated position. Remote adjustment may be mechanical by means of bowden cables, or may be electric by means of geared motors. The mirror glass may also be electrically heated and may include electrochromic dimming to reduce glare to the driver from the headlamps of following vehicles. Increasingly, the side mirror incorporates the vehicle's turn signal repeaters. There is evidence to suggest mirror-mounted repeaters may be more effective than repeaters mounted in the previously predominant fender side location.^[1]

Wing mirror on Korean-specification vehicle. Legend in Korean reads "Objects in mirror are closer than they appear".

Driver's control for Wing mirrors, with tiny curb-view button (saab 9-5).

Optional side mirror

In the 1940s many roads were unpaved and had two lanes, one in each direction. Drivers had to be aware only of traffic on their side and directly behind them (rear view). Due to this, most passenger vehicles with an internal rear-view mirror until the late 1960s had the passenger-side mirror only as an optional addition, as it was considered a luxury.

Planar, convex, aspheric

In the U.S. and Canada, the U.S. National Highway Traffic Safety Administration's Federal Motor Vehicle Safety Standard 111 and the Canada Motor Vehicle Safety Standard 111 require the driver side mirror to provide "unit magnification", i.e., an undistorted 1:1 reflection achieved with a flat mirror. However, unit magnification limits the field of view that can be provided by a mirror of size compatible with the vehicle body. The ECE regulations in use throughout most of the world except North America permit the driver side mirror to have a planar, convex, or aspheric surface; an aspheric section is often combined with a larger convex section, and the two sections are separated by a visible line to alert the driver to the two sections' different perspective shifts.^[2][3]

Because of the distance from the driver's eye to the passenger side mirror, a useful field of view can be achieved only with a convex or aspheric mirror. However, the convexity also minifies the objects shown. Since such objects seem farther away than they actually are, a driver might make a maneuver such as a lane change assuming an adjacent vehicle is a safe distance behind, when in fact it is quite a bit closer.^[4] In the United States,^[5]Canada,^[6]India, Korea and Australia^{[citation needed]}, non-planar mirrors are etched or printed with the warning legend .mw-parser-output .smallcaps{font-variant:small-caps}objects in the mirror are closer than they appear. In Canada, this warning is often supplemented by a transparent decal on the passenger side window repeating the warning in French: les objets dans le retroviseur sont plus proche qu'ils ne le paraissent. In Korea, the warning appears in Korean. Warnings of this nature are not required in Europe.

Wing mirror retraction control (Saab 9-5)

Other requirements

Most side mirrors^{[according to whom?]} may be manually or electrically folded in, to protect them when the car is parked or being washed in an automated car wash. Passing cars can easily clip protruding wing mirrors; the folding capability helps protect them from harm.
ECE Regulation 46 requires that side mirrors be mounted such that they swing away when struck by a test cylinder meant to represent a pedestrian.^[7]

Until 1983, Japanese national regulations required sideview mirrors to be visible to the driver through the windshield area swept by the windshield wipers, so the mirrors were mounted far forward atop the front fenders. More recent Japanese-specification vehicles have side mirrors similar to those in other countries.^[8]

U.S. Federal Motor Vehicle Safety Standard 111 requires that convex side view mirrors must have a curvature radius of between 889 mm and 1651 mm.^[5] Canada Motor Vehicle Safety Standard 111 stipulates a range of between 890 mm and 1800 mm.^[6] Neither the U.S. nor the Canadian standard allows for aspheric mirrors.^[3] The European ECE Regulation 46 used throughout most of the world permits planar, convex, and/or aspheric mirrors on either side of the vehicle.^[3][7] American research suggests non-planar driver side mirrors may help reduce crashes.^[2][9]

See also

References

Look up wing mirror in Wiktionary, the free dictionary.